Home > Introduction To Engineering > Quizzes > Intro To Engineering Design - 2
Intro To Engineering Design - 2
Fast practice, instant feedback. Timer auto-submits when time’s up.
Avg score: 40% • Most missed: “A part of design brief that challenges the designer - describes what a design so…”
Intro To Engineering Design - 2
Time left 00:00
25 Questions

1. A slot in a shaft to receive a key.

2. Lines that are used to represent the material through which a cut is made in order to show an interior sectional view.

3. The designation of the size established for a commercial product.

4. A conical- shaped recess around a hole - often used to receive a tapered screw.

5. A shallow recess like a counterbore - used to provide a good bearing surface for a fastener.

6. A line drawn on a view where a cut was made in order to define the location of the imaginary section plane.

7. A tolerance in which variation is permitted in both directions from the specified dimension.

8. A group of values that is used to analyze the distribution of data.

9. A dimensioning system which requires all numerals - figures - and notes to be lettered horizontally and be read from the bottom of the drawing sheet.

10. A theoretically exact point - axis - or plane derived from the true geometric counterpart of a specific datum feature. The origin from which the location - or geometric characteristic of a part feature - is established.

11. The largest size limit of an external feature and the smallest size limit of an internal feature.

12. To draw a figure within another so that their boundaries touch but do not intersect.

13. A line used to show the alternate positions of an object or matching part without interfering with the main drawing.

14. A graph of vertical bars representing the frequency distribution of a set of data.

15. A dimensioning system where each dimension originates from a common surface - plane - or axis. Also known as baseline dimensioning.

16. A part of design brief that challenges the designer - describes what a design solution should do without describing how to solve the problem - and identifies the degree to which the solution must be executed.

17. An orthographic view of an object using a direction of sight other than one of the six basic views (front - top - right- side - rear - bottom - left- side); used to show a surface that is not parallel to any of the principal view planes.

18. Constant - non - numerical relationships between the parts of a geometric figure. Examples include parallelism - perpendicularity - and concentricity.

19. 1. A manufacturing process that forces material through a shaped opening. 2. A modeling process that creates a three- dimensional form by defining a closed two- dimensional shape and a length.

20. 1. A triangle located round a polygon such as a circle. 2 To draw a figure around another - touching it at points but not cutting it.

21. A number value - or algebraic equation that is used to control the size or location of a geometric figure.

22. A rectangular coordinate system created by three mutually perpendicular coordinate axes - commonly labeled X - Y - and Z.

23. 1. For design - the use of a computer to assist in the process of designing a part - circuit - building - etc. 2. For drafting - the use of a computer to assist in the process of creating - storing - retrieving - modifying - plotting - and communicat

24. A system of dimensioning which requires all numerals - figures - and notes to be aligned with the dimension lines so that they may be read from the bottom (for horizontal dimensions) and from the right side (for vertical dimensions).

25. A rounded interior blend between two surfaces. Some uses are to strengthen joining surfaces or to allow a part to be removed from a mold.

⚡ Recently practiced quizzes in this topic
Live quiz activity
NOCTI Pre Engineering Review Applied Physics 1: Engineering Materials And Applications Intro To Engineering Design Common Hand Tools Engineering Graphics Engineering Mechanics: Friction NOCTI Pre Engineering Exam Study Guide Applied Chemistry 2: Corrosion Technical Drawing Terms Hand Tools
 
❤ If you liked Fatskills, consider supporting us by checking out The Life Manuals You Never Got.

🌈  Our mission is to help improve your scores in any subject and exam withonline quizzes, practice tests, study guides, & advice for students. Since 2018.
About | Explore | User Guide | Topics | Subjects | Doubt Solver | Career Aptitude Test | Answers | Free Tools | OSHA Basics Quiz | What Should We Know?
Privacy | Terms |
Without work one finishes nothing. - Ralph Waldo Emerson
© 2026 Fatskills.com

All trademarks, logos and brand names are the property of their respective owners. All company, product and service names used in this website are for identification purposes only. Use of these names, trademarks and brands does not imply endorsement.