Home > National Electrical Code (NEC) exam > Quizzes > National Electrical Code 2023 Basics: Grounding and Bonding
National Electrical Code 2023 Basics: Grounding and Bonding
Fast practice, instant feedback. Timer auto-submits when time’s up.
Avg score: 0% • Most missed: “Regulation that can be violated by neutral-to-ground connections downstream of a…”
NEC Article 250 covers grounding and bonding to ensure electrical safety by stabilizing voltage and providing a low-impedance path for fault current. Grounding connects the system to the earth, while Bonding links metallic parts for continuity. Proper grounding and bonding ensure overcurrent devices trip, protecting against shocks.  Key Grounding and Bonding Concepts: Grounding Electrode System (NEC 250.52): A reliable, direct connection to the earth, such as a ground rod, concrete-encased electrode (Ufer), or metal water pipe, must be used. Grounding Electrode Conductor (GEC): Connects... Show more
National Electrical Code 2023 Basics: Grounding and Bonding
Time left 00:00
25 Questions

1. 250.28(A) through (D)

2. A system that derives its power from a source that is not connected to the supply system.

3. must contain an insulated grounded (neutral) conductor and a separate equipment grounding conductor

4. If the grounding electrode for a separate building or structure is only a single ground rod or two ground rods, the maximum-size copper grounding electrode conductor required is 6 AWG.

5. 10 AWG copper.

6. Table 250.102(C)(1)

7. To minimize potential differences between IT equipment and other conductive materials and equipment in an information technology room.

8. A required connection point for intersystem bonding conductors at service equipment or metering equipment enclosure and at the disconnecting means for additional buildings or structures.

9. A grounding electrode connection is required to be made at a location anywhere from the load end of the overhead service conductors.

10. Where more than one separately derived system is grounded using a common grounding electrode conductor, the common grounding electrode conductor shall be sized based at not less than 3/0 AWG copper or 250 kcmil aluminum.

11. Conductors for radio and television antenna systems that shall not be installed within 18 inches of the earth.

12. Must be connected within 5 feet from its point of entrance to the building.

13. ground, grounded metal parts, and any equipment grounding conductor(s)

14. Shall not be smaller than 14 AWG copper.

15. Where the utility transformer supplying a service is located outside the building, a grounding connection is not required to be made outside a building or structure served by a grounded electrical service.

16. Installation at outlets is not a common contributor to objectionable current.

17. Generally must qualify as an equipment grounding conductor, and an insulated equipment grounding conductor must be contained within the assembly for direct connection to an isolated grounding type receptacle

18. A solar photovoltaic system that is functionally grounded is one that has an electrical ground reference for operational purposes and is not solidly grounded.

19. Circulating currents in the grounding paths.

20. A 3-phase, 4-wire, delta-connected system where the midpoint of one phase winding is used as a circuit conductor is permitted to be grounded, but not required to be grounded.

21. If any grounding electrodes are present at a building or structure served by electrical power, the electrodes must be bonded together to form a grounding electrode system.

22. An approved means for external connection of a bonding or grounding electrode conductor.

23. An enclosure that contains the service equipment for a separately derived system.

24. Three methods for connecting the grounding electrode conductor taps to the common grounding electrode conductor at an accessible location include: I. A connector listed as grounding and bonding equipment, II. An intersystem bonding termination, III. A soldered connection, IV. The exothermic welding process, V. Listed connections to aluminum or copper busbars not less than 1/4 × 2"."

25. Shall be grounded by connecting them to the equipment grounding conductor of the supplying branch circuit or feeder.

⚡ Recently practiced quizzes in this topic
Live quiz activity
NEC 2023 Basics NEC Grounding & Bonding (Article 250) NEC Load Calculations (Article 220) NEC-Electrician: Conduit-Fill Basics NEC 430 Motors and Controllers NEC Article 300. General Requirements for Wiring Methods and Materials NEC 2023: Electrical Branch Circuits and Receptacle Requirements NEC Practice Exam Questions National Electrical Code (NEC) 2023: Important Sections and Safety Standards NEC Wiring Methods & Raceways
 
❤ If you liked Fatskills, consider supporting us by checking out The Life Manuals You Never Got.

🌈  Our mission is to help improve your scores in any subject and exam withonline quizzes, practice tests, study guides, & advice for students. Since 2018.
About | Explore | User Guide | Topics | Subjects | Doubt Solver | Career Aptitude Test | Answers | Free Tools | OSHA Basics Quiz | What Should We Know?
Privacy | Terms |
Without work one finishes nothing. - Ralph Waldo Emerson
© 2026 Fatskills.com

All trademarks, logos and brand names are the property of their respective owners. All company, product and service names used in this website are for identification purposes only. Use of these names, trademarks and brands does not imply endorsement.